=> run setargs_mmc => run boot_dsp0 dsp0:gpio init config fail DSP0 start ok, img length 252960, booting from 0x400660 => run boot_normal Android's image name: d1-nezha No reserved memory region found in source FDT [33.608] Starting kernel ... [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Linux version 5.4.61 (wuhuabin@AwExdroid86) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #51 PREEMPT Mon May 10 12:41:05 UTC 2021 [ 0.000000] cma: Reserved 8 MiB at 0x00000000bf800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000bfffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x00000000bfffffff] [ 0.000000] On node 0 totalpages: 523776 [ 0.000000] DMA32 zone: 7161 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 523776 pages, LIFO batch:63 [ 0.000000] elf_hwcap is 0x20112d [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516615 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 rootwait init=/sbin/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:recovery@ubi0_7:UDISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun20iw1p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.05-00107-gc22c3d075c(04/24/2021-07:52:58) mbr_offset=1556480 disp_reserve [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Sorting __ex_table... [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 2040724K/2095104K available (5944K kernel code, 655K rwdata, 2062K rodata, 208K init, 251K bss, 46188K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000023] riscv_timer_clockevent depends on broadcast, but no broadcast function available [ 0.000327] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000929] Console: colour dummy device 80x25 [ 0.000970] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000985] pid_max: default: 32768 minimum: 301 [ 0.001196] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.001232] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002949] ASID allocator initialised with 65536 entries [ 0.003114] rcu: Hierarchical SRCU implementation. [ 0.003899] devtmpfs: initialized [ 0.015821] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0 [ 0.016720] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016750] futex hash table entries: 256 (order: 0, 6144 bytes, linear) [ 0.017177] pinctrl core: initialized pinctrl subsystem [ 0.018502] NET: Registered protocol family 16 [ 0.020451] DMA: preallocated 256 KiB pool for atomic allocations [ 0.021077] cpuidle: using governor menu [ 0.066073] rtc_ccu: sunxi ccu init OK [ 0.072499] clock: sunxi ccu init OK [ 0.073427] clock: sunxi ccu init OK [ 0.112309] iommu: Default domain type: Translated [ 0.112480] sunxi iommu: irq = 4 [ 0.113676] SCSI subsystem initialized [ 0.114019] usbcore: registered new interface driver usbfs [ 0.114119] usbcore: registered new interface driver hub [ 0.114222] usbcore: registered new device driver usb [ 0.114401] mc: Linux media interface: v0.10 [ 0.114462] videodev: Linux video capture interface: v2.00 [ 0.115422] Advanced Linux Sound Architecture Driver Initialized. [ 0.116014] Bluetooth: Core ver 2.22 [ 0.116093] NET: Registered protocol family 31 [ 0.116105] Bluetooth: HCI device and connection manager initialized [ 0.116124] Bluetooth: HCI socket layer initialized [ 0.116136] Bluetooth: L2CAP socket layer initialized [ 0.116170] Bluetooth: SCO socket layer initialized [ 0.116453] pwm module init! [ 0.117978] g2d 5410000.g2d: Adding to iommu group 0 [ 0.118459] G2D: rcq version initialized.major:250 [ 0.119003] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.120615] clocksource: Switched to clocksource riscv_clocksource [ 0.132340] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.147989] NET: Registered protocol family 2 [ 0.148766] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.148864] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.149060] TCP bind hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.149216] TCP: Hash tables configured (established 16384 bind 16384) [ 0.149401] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.149503] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.149819] NET: Registered protocol family 1 [ 0.151140] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 0.151709] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.151974] sunxi_spi_resource_get()2062 - [spi0] SPI MASTER MODE [ 0.152084] sunxi_spi_clk_init()2138 - [spi0] mclk 100000000 [ 0.152750] sunxi_spi_probe()2542 - [spi0]: driver probe succeed, base ffffffd00405a000, irq 31 [ 0.154624] Initialise system trusted keyrings [ 0.154870] workingset: timestamp_bits=62 max_order=19 bucket_order=0 [ 0.162439] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.183602] Key type asymmetric registered [ 0.183617] Asymmetric key parser 'x509' registered [ 0.183640] io scheduler mq-deadline registered [ 0.183648] io scheduler kyber registered [ 0.183668] atomic64_test: passed [ 0.184857] [DISP]disp_module_init [ 0.185418] disp 5000000.disp: Adding to iommu group 0 [ 0.186026] [DISP] disp_init,line:2385: [ 0.186032] smooth display screen:0 type:1 mode:4 [ 0.222469] display_fb_request,fb_id:0 [ 0.252287] disp_al_manager_apply ouput_type:1 [ 0.252449] [DISP] lcd_clk_config,line:731: [ 0.252462] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000) [ 0.252462] clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000) [ 0.252859] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.253600] [DISP]disp_module_init finish [ 0.254515] sunxi_sid_init()497 - insmod ok [ 0.255064] pwm-regulator: supplied by regulator-dummy [ 0.262270] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 0.262713] uart uart0: get regulator failed [ 0.262744] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.263069] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.263096] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.051564] printk: console [ttyS0] enabled [ 1.057136] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.068597] uart uart1: get regulator failed [ 1.073422] uart uart1: uart1 supply uart not found, using dummy regulator [ 1.081522] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI [ 1.091417] misc dump reg init [ 1.095466] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 1.102708] sunxi-rfkill soc@3000000:rfkill@0: devm_pinctrl_get() failed! [ 1.110320] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 1.117639] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 1.125096] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 1.131632] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 1.138542] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 1.146304] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 1.154163] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 1.162330] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 1.169947] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 1.176757] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 1.184291] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 1.192594] [ADDR_MGT] addr_mgt_probe: module version: v1.0.8 [ 1.200106] [ADDR_MGT] addr_mgt_probe: success. [ 1.206204] sunxi-spinand: AW SPINand MTD Layer Version: 2.0 20201228 [ 1.213478] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306 [ 1.221374] sunxi-spinand-phy: not detect any munufacture from id table [ 1.228780] sunxi-spinand-phy: get spi-nand Model from fdt fail [ 1.235441] sunxi-spinand-phy: get phy info from fdt fail [ 1.241524] sunxi-spinand-phy: not detect munufacture from fdt [ 1.248205] sunxi-spinand-phy: detect munufacture from id table: Mxic [ 1.255453] sunxi-spinand-phy: detect spinand id: ff0326c2 ffffffff [ 1.262463] sunxi-spinand-phy: ========== arch info ========== [ 1.268963] sunxi-spinand-phy: Model: MX35LF2GE4AD [ 1.275711] sunxi-spinand-phy: Munufacture: Mxic [ 1.281655] sunxi-spinand-phy: DieCntPerChip: 1 [ 1.287300] sunxi-spinand-phy: BlkCntPerDie: 2048 [ 1.293244] sunxi-spinand-phy: PageCntPerBlk: 64 [ 1.298967] sunxi-spinand-phy: SectCntPerPage: 4 [ 1.304647] sunxi-spinand-phy: OobSizePerPage: 64 [ 1.310372] sunxi-spinand-phy: BadBlockFlag: 0x1 [ 1.316216] sunxi-spinand-phy: OperationOpt: 0x7 [ 1.322092] sunxi-spinand-phy: MaxEraseTimes: 65000 [ 1.328108] sunxi-spinand-phy: EccFlag: 0x2 [ 1.333951] sunxi-spinand-phy: EccType: 8 [ 1.339595] sunxi-spinand-phy: EccProtectedType: 3 [ 1.345248] sunxi-spinand-phy: ======================================== [ 1.352670] sunxi-spinand-phy: [ 1.356168] sunxi-spinand-phy: ========== physical info ========== [ 1.363076] sunxi-spinand-phy: TotalSize: 256 M [ 1.368429] sunxi-spinand-phy: SectorSize: 512 B [ 1.373789] sunxi-spinand-phy: PageSize: 2 K [ 1.378932] sunxi-spinand-phy: BlockSize: 128 K [ 1.384290] sunxi-spinand-phy: OOBSize: 64 B [ 1.389545] sunxi-spinand-phy: ======================================== [ 1.396939] sunxi-spinand-phy: [ 1.400435] sunxi-spinand-phy: ========== logical info ========== [ 1.407275] sunxi-spinand-phy: TotalSize: 256 M [ 1.412633] sunxi-spinand-phy: SectorSize: 512 B [ 1.417986] sunxi-spinand-phy: PageSize: 4 K [ 1.423153] sunxi-spinand-phy: BlockSize: 256 K [ 1.428489] sunxi-spinand-phy: OOBSize: 128 B [ 1.433876] sunxi-spinand-phy: ======================================== [ 1.441395] sunxi-spinand-phy: block lock register: 0x00 [ 1.447481] sunxi-spinand-phy: feature register: 0x11 [ 1.453181] sunxi-spinand-phy: sunxi physic nand init end [ 1.459826] Creating 4 MTD partitions on "sunxi_mtd_nand": [ 1.466080] 0x000000000000-0x000000100000 : "boot0" [ 1.481879] 0x000000100000-0x000000500000 : "uboot" [ 1.487995] random: fast init done [ 1.521790] 0x000000500000-0x000000600000 : "secure_storage" [ 1.541795] 0x000000600000-0x000010000000 : "sys" [ 1.934219] random: crng init done [ 2.682327] libphy: Fixed MDIO Bus: probed [ 2.686930] CAN device driver interface [ 2.692787] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 2.704155] sunxi gmac driver's version: 1.0.0 [ 2.709254] gmac-power0: NULL [ 2.712606] gmac-power1: NULL [ 2.715911] gmac-power2: NULL [ 2.720369] Failed to alloc md5 [ 2.723967] eth0: Use random mac address [ 2.728700] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.736116] sunxi-ehci: EHCI SUNXI driver [ 2.741229] get ehci1-controller wakeup-source is fail. [ 2.747155] sunxi ehci1-controller don't init wakeup source [ 2.753498] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0008d6748, 0x:ffffffd004079000, irq_no:31 [ 2.767093] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 2.779678] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 2.786994] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 2.796821] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 [ 2.830664] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 2.838437] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device connect [ 2.847977] hub 1-0:1.0: USB hub found [ 2.852295] hub 1-0:1.0: 1 port detected [ 2.857473] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.864509] sunxi-ohci: OHCI SUNXI driver [ 2.869554] get ohci1-controller wakeup-source is fail. [ 2.875566] sunxi ohci1-controller don't init wakeup source [ 2.881867] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0008d7288 [ 2.892303] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 2.904853] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 2.912171] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 2.921971] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 [ 2.995622] hub 2-0:1.0: USB hub found [ 2.999858] hub 2-0:1.0: 1 port detected [ 3.005349] usbcore: registered new interface driver uas [ 3.011559] usbcore: registered new interface driver usb-storage [ 3.018334] usbcore: registered new interface driver ums-alauda [ 3.025148] usbcore: registered new interface driver ums-cypress [ 3.031963] usbcore: registered new interface driver ums-datafab [ 3.038726] usbcore: registered new interface driver ums_eneub6250 [ 3.045777] usbcore: registered new interface driver ums-freecom [ 3.052582] usbcore: registered new interface driver ums-isd200 [ 3.059276] usbcore: registered new interface driver ums-jumpshot [ 3.066177] usbcore: registered new interface driver ums-karma [ 3.072955] usbcore: registered new interface driver ums-onetouch [ 3.079907] usbcore: registered new interface driver ums-realtek [ 3.086748] usbcore: registered new interface driver ums-sddr09 [ 3.093513] usbcore: registered new interface driver ums-sddr55 [ 3.100173] usbcore: registered new interface driver ums-usbat [ 3.107954] sunxi_gpadc_init,1968, success [ 3.114782] sunxi-rtc 7090000.rtc: registered as rtc0 [ 3.120534] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:02:16 UTC (136) [ 3.129696] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 3.135586] i2c /dev entries driver [ 3.139608] IR NEC protocol handler initialized [ 3.145390] sunxi cedar version 1.1 [ 3.149553] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 3.156000] VE: install start!!! [ 3.156000] [ 3.161544] VE: cedar-ve the get irq is 6 [ 3.161544] [ 3.167854] VE: ve_debug_proc_info:0000000047abc5b9, data:00000000a986e455, lock:0000000056eeb6ca [ 3.167854] [ 3.179482] VE: install end!!! [ 3.179482] [ 3.185424] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 3.194631] Bluetooth: HCI UART driver ver 2.3 [ 3.199589] Bluetooth: HCI UART protocol H4 registered [ 3.205404] Bluetooth: HCI UART protocol BCSP registered [ 3.211352] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 3.218615] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1 [ 3.225037] usb 1-1: new high-speed USB device number 2 using sunxi-ehci [ 3.232615] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1 [ 3.239170] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled! [ 3.239170] [ 3.247906] [XR_BT_LPM] bluesleep_probe: uart_index(1) [ 3.257727] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 3.267723] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 3.273996] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 3.280326] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 3.286792] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 3.293229] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 3.299731] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 3.306289] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 3.312818] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 3.319777] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 3.325296] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 3.332078] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.343267] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 3.363451] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.387865] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 3.393585] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.406012] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 3.416130] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 3.422419] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 3.428782] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 3.435269] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.446856] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 3.453377] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 3.460089] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 3.466775] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 3.473450] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 3.480099] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 3.488853] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.501643] hub 1-1:1.0: USB hub found [ 3.506289] hub 1-1:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.515330] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.526479] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.538156] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 3.558413] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.582700] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 3.590359] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.597516] sunxi_led_probe()1715 - start [ 3.602028] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.608917] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.620582] sunxi_get_str_of_property()1560 - failed to get the string of propname led_regulator! [ 3.630727] sunxi_register_led_classdev()1448 - led_classdev start [ 3.639363] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.654238] sunxi_led_probe()1820 - finish [ 3.659527] usbcore: registered new interface driver usbhid [ 3.665831] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.674959] usbhid: USB HID core driver [ 3.680086] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.686893] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.698351] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.705962] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.713088] usbcore: registered new interface driver snd-usb-audio [ 3.720003] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.726802] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 3.738123] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.753637] sunxi-daudio 2034000.daudio: regulator missing or invalid [ 3.761493] [AUDIOCODEC][sunxi_codec_parse_params][2208]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 3.761493] [ 3.778821] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 3.790549] [AUDIOCODEC][sunxi_codec_parse_params][2244]:adcdrc_cfg:0, adchpf_cfg:0, dacdrc_cfg:0, dachpf:0 [ 3.801524] mmc0: new high speed SDHC card at address b078 [ 3.808482] [AUDIOCODEC][sunxi_internal_codec_probe][2380]:codec probe finished [ 3.817518] mmcblk0: mmc0:b078 SB32G 29.7 GiB [ 3.823591] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 3.835545] [SNDCODEC][sunxi_card_init][583]:card init finished [ 3.844549] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 3.855938] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [ 3.868026] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished [ 3.877420] NET: Registered protocol family 10 [ 3.883945] Segment Routing with IPv6 [ 3.888224] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.895696] NET: Registered protocol family 17 [ 3.900751] can: controller area network core (rev 20170425 abi 9) [ 3.907780] NET: Registered protocol family 29 [ 3.912810] can: raw protocol (rev 20170425) [ 3.917568] can: broadcast manager protocol (rev 20170425 t) [ 3.923969] can: netlink gateway (rev 20190810) max_hops=1 [ 3.930400] Bluetooth: RFCOMM TTY layer initialized [ 3.935994] Bluetooth: RFCOMM socket layer initialized [ 3.941784] Bluetooth: RFCOMM ver 1.11 [ 3.946991] Loading compiled-in X.509 certificates [ 3.954759] HDMI 2.0 driver init start! [ 3.959050] boot_hdmi=false [ 3.962290] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 3.969321] HDMI2.0 module init end [ 3.999035] twi twi2: twi2 supply twi not found, using dummy regulator [ 4.014322] pcf857x 2-0038: probed [ 4.024472] sunxi_i2c_probe()2262 - [i2c2] probe success [ 4.040484] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present! [ 4.050909] sunxi-audio-card 2031060.sounddmic: snd-soc-dummy-dai <-> 2031000.dmic mapping ok [ 4.061774] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present! [ 4.072396] sunxi-audio-card 20340a0.sounddaudio2: snd-soc-dummy-dai <-> 2034000.daudio mapping ok [ 4.084128] get ehci0-controller wakeup-source is fail. [ 4.090063] sunxi ehci0-controller don't init wakeup source [ 4.096349] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008d6388, 0x:ffffffd005422000, irq_no:2e [ 4.109899] [sunxi-ehci0]: Not init ehci0 [ 4.114922] get ohci0-controller wakeup-source is fail. [ 4.120907] sunxi ohci0-controller don't init wakeup source [ 4.127125] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008d6ec8 [ 4.137594] [sunxi-ohci0]: Not init ohci0 [ 4.145137] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.156549] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.164188] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.173892] clk: Not disabling unused clocks [ 4.178685] ALSA device list: [ 4.182130] cfg80211: failed to load regulatory.db [ 4.187547] #0: audiocodec [ 4.190836] #1: snddmic [ 4.193755] #2: sndhdmi [ 4.196708] alloc_fd: slot 0 not NULL! [ 4.201384] VFS: Cannot open root device "mmcblk0p5" or unknown-block(179,5): error -6 [ 4.210213] Please append a correct "root=" boot option; here are the available partitions: [ 4.219670] 1f00 1024 mtdblock0 [ 4.219673] (driver?) [ 4.227017] 1f01 4096 mtdblock1 [ 4.227021] (driver?) [ 4.234414] 1f02 1024 mtdblock2 [ 4.234418] (driver?) [ 4.241734] 1f03 256000 mtdblock3 [ 4.241737] (driver?) [ 4.249044] b300 31166976 mmcblk0 [ 4.249049] driver: mmcblk [ 4.256668] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,5) [ 4.266078] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.61 #51 [ 4.272567] Call Trace: [ 4.275304] [] walk_stackframe+0x0/0xa0 [ 4.281320] [] show_stack+0x2a/0x34 [ 4.286949] [] dump_stack+0x20/0x28 [ 4.292579] [] panic+0xee/0x2b6 [ 4.297824] [] mount_block_root+0x1ee/0x28a [ 4.304227] [] mount_root+0x86/0x90 [ 4.309855] [] prepare_namespace+0x110/0x152 [ 4.316354] [] kernel_init_freeable+0x17e/0x19a [ 4.323150] [] kernel_init+0x12/0xee [ 4.328878] [] ret_from_exception+0x0/0xc [ 4.335092] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,5) ]---